High made in China – replacement parts – in Kolhapur India Efficiency Metal Sheet C Purlins Roll Forming Machine with ce certificate top quality low price

We – EPG Group the bigge EPT Chain and agricultural gearbox manufacturing unit in China with 5 various branches. For far more information: Cellular/whatsapp/telegram/Kakao us at: 0086~13083988828 13858117778 0571 88828

CZ Steel Purlins Roll Forming Equipment Manufacturing Line Equipment

(1)The main complex parameter
one.Rolling solution specification:width 100mm~300mm,higher 40mm~80mm,thickness2.0mm~3.0mm
two.The speed of rolling:twelve-fifteen m/min
3.Number of sets of molding:17 sets main roller
four.Amount of sets of leveling: 7 sets leveling roller
five.Change line:2 sets
six.Set up kind:Adopt arch kind
seven.Roller kind: use break up sort
eight.Roll materials: GCr15 quenching remedy, HRC58-62
9.Spindle content: 45 high quality metal quenched and tempered
10.major motor energy:15KW
11. EPT station motor power:7.5KW
12.Adjust the technical specs velocity: a entire set of ten minutes
thirteen.The method of Slicing and punching:Following forming then punching and last but not least chopping
fourteen.The material of cutting knife and punching mould:Cr12 quenching remedy.
fifteen.Digital management technique:The complete equipment use  industrial personal computer PLC Siemens frequency conversion to control.
16.Major device size:size 11m×width 2.3m×high 1.6m (such as main motor)
17.Total fat of equipment:About 12000kg
(2)Composition of products:
one.Xihu (We EPT Lake) Dis.
To avoid the plate go in manufacturing approach to maintain the solution good quality.
two.leveling device
The leveling equipment is compose of plate materials guiding device,guidebook plate driving roller, adjustable guide system on each sides, leveling roller and and so on.
The leveling device have a individual motor travel and the velocity is slower than principal generate motor. In the head of the reducer shaft set up overrunning clutch.Firstly the  motor generate feeding content,then workpieces into main generate roller, and owing to the effect of the overrunning clutch, the front drive motor is in a passive state.
Owing to the principal diver motor’s velocity is more rapidly than entrance generate motor,when plate substance slicing down,in between the workpieces will have a distance.
When a batch of workpieces are finish, the steel coil demands to be take away,and the entrance generate motor will be quit.When all the end workpieces are fully out of the roll forming device, the front travel motor will inverse motion and  exit the steel coil.
three. EPT punching device: 
composition type: EPT punching gadget rack is use gantry type. The energy resource is the force of underneath oil cylinder:The hole placement is longitudinally set and can be adjusted transversely.
 Main parameter:

• Greatest punching plate thickness:3mm
• The horizontal adjustment selection of punching hole distance :45~500mm

four. EPT reducing system: 
Function:After enter the size parameter of workpiece via PLC,the encoder will counting size and when the workpiece size is sufficient the hydraulic cutting device will lower down the workpiece.
Main parameter:

1. Optimum cutting plate thickness:3mm
2. Powerful slicing width of workpiece:650mm

five.Roll forming machine able of rapidly altering sort:
The roll forming device is compose of drive motor, frame, forming roller,Handbook regulating workpieces requirements gadget.

1. forming roller driving motor using 15kw hardened gears reducer ,frequency control and encoder control brake.
2. The frame uses the channel metal as the principal beam,and the middle is welded by the stiffener plate.
3. The forming roller is use the method of two sides shaped and the sort of center minimize off. The forming roller through the motor pushed sliding screw rod to adju EPT the workpieces technical specs. Between the two sliding screw rod use the bevel gear to travel and produced them to attain full synchronization also with self-locking operate. The thickness of the steel plate is modified by changing the eccentricity length of the passive roller.

(3)Tools production method
feeding  –  guiding  –   leveling –     punching –     slicing  – forming –  tropsch feed

자주 묻는 질문
1)Q:Can you make equipment according to my layout?
   A:Of course, we have seasoned technical team to function out the suited layout for you and verify with you till you concur.
2) Q: Will you deliver the correct items as ordered? How can I tru EPT you?
    A: Yes, we will. The main of our organization culture is honesty and credit.
three)Q:What payment phrases you take?
    A:Typically is TT, 30% deposit and 70% prior to shipment, and occasionally we can think about far more for you as for each your ask for.
four) Q:What is the warranty for our device?
    A:We have a single year ensure, and supply entire life’s specialized support.

The use of unique tools manufacturer’s (OEM) element quantities or logos , e.g. CASE® and John Deere® are for reference reasons only and for indicating item use and compatibility. Our firm and the shown substitute parts contained herein are not sponsored, authorized, or made by the OEM.